Sorensen Power Supply ETS TerraSAS

Product Overview
For microgrids, energy storage, and inverter test applications, the TerraSASâ„¢ series photovoltaic (PV) simulators are specifically designed to emulate the dynamic electrical behavior of a terrestrial PV solar array. They offer low output capacitance and high closed loop bandwidth to keep up with the advanced Maximum Power Point Tracking (MPPT) algorithms used in today's grid-tied inverters.

The ETS Embedded TerraSAS is a high performance solution in a small form factor that combines an agile power supply with an innovative I-V curve generator in a single standalone unit.

ETS1000: For non-isolated string inverters up to 1000Vdc Voc.
ETS600: For use with string inverters that contain transformer isolation up to 600Vdc Voc.
ETS80: For use with micro-inverters or DC optimizers up to 80Vdc Voc

The ETS series standalone TerraSAS consists of a programmable DC power supply with control software and GUI interface, output isolation, and a unique PV simulation engine that provides the I-V curve. This combination of hardware, software, and firmware allows the TerraSAS to simulate test protocols or combinations of events that a real-world solar installation will be subjected to.

The included software allows modeling of a PV panel without an extensive knowledge of solar array parameters. The only parameters required for a simulation are the open circuit voltage (Voc), short circuit current (Isc), and the peak power parameters Vmpp and Impp. Changes to these parameters allow the shape of the I-V curve to be
adapted to any fill factor between 0.5 and 0.95.

Once an I-V curve has been generated, changes to the irradiation level or temperature can be modified on the fly to test the behavior of a grid tied inverter under realistic conditions for cloud shadowing and panel temperature rise. Long term weather simulations can be loaded and run to determine the amount of energy harvest delivered in a given situation. Inverter designers use these accuracy and efficiency tests to optimize real MPP search modes.

Application
Many solar inverters generate AC ripple on their DC input, which is connected to the photovoltaic array. For single phase inverters, the frequency of this ripple is twice the line frequency (120 Hz for US models). The simulator's power supplies must not suppress this ripple as a function of their regulation loop. An increasing number of inverters (and virtually all micro-inverters) accurately measure amplitude and phase of the ripple voltage and current to quickly track the MPP of the array. This approach allows tracking the MPP at a much higher speed when compared to conventional dithering techniques (also called perturbate-and-observe). Faster tracking of the MPP results in a much higher overall efficiency in cloudy conditions, where the irradiance is constantly changing. It is likely that all solar inverters will use this approach in the near future, since end users are very sensitive to the overall efficiency of their solar energy installations. To satisfy this requirement, the PV simulator must be capable of reproducing the voltage / current behavior of a solar array at the ripple frequency. Most standard switching power supplies employ very large output capacitors and inductors in their output circuits and are unable to deliver the
required performance - regardless of the response speed of the I-V curve controller. Elgar's TerraSAS line of PV simulators are based on high speed versions of our standard products, where output capacitors and other speed-limiting components have been adjusted. This results in a speed improvement of 10 times or better.

Proprietary features built into the PV controller hardware and firmware, combined with our high speed power supplies, deliver the required performance. This technology was extensively tested on micro-inverters and is ready to test the next generation of inverters. The required performance is delivered by high speed switching power supplies and advanced DSP signal processing techniques. In some conditions traditional DC power sources using IGBT technology do not meet MPPT response speed requirements, depending on the MPPT principles. Our power supplies use Power MOSFETs, which typically switch ten times as fast as the most recent IGBTs. Higher switching frequency translates to smaller output capacitors and inductors - which is the key to a successful high speed power supply design

Scalability
Power supplies are available in 850W, 5kW, 10kW, and 15KW increments. The 80V units are available in two power levels: 1200W for microinverters and 850W for DC power optimizers. The bandwidth on the 850W version has been improved to 2kHz by adding a linear regulation output stage. 600V units are available in 5kW, 10kW, and 15kW versions depending on Isc requirements. 1000V units are available in 5kW and 10kW versions depending on Isc requirements. All versions are easily connected in parallel to scale output power up to handle microinverters, string inverters, and even utility scale inverters. Many models can also be connected in series to handle higher voltage tests. Please refer to the connection diagrams located in the User Manual and follow appropriate wiring codes before connecting ETS PV simulators in series or parallel.

Real time I-V curve display
The Elgar Real time I-V curve display is updated 20 times per second to illustrate dynamic inverter behavior (operating point and sweep amplitude). Compared to other commercially available solar array simulators with an update rate of only 1Hz, this allows more accurate analysis of the inverter's actual MPP tracking ability.

Sorensen Power Supply Elgar XWave Series
Peak Inrush Current

Sorensen Power Supply MX Series
1Ã¸ to 3Ã¸ Power

Sorensen Power Supply (CW) Series
Product OverviewThe ContinuousWave (CW) Series of AC power sources provides clean single phase power at an impressive price/performance ratio. These compact switch mode sources

Sorensen Power Supply RP Series
1Ã¸ to 3Ã¸ VA

Sorensen Power Supply Radar Power Bus Simulation
Industry : space power Application : power bus Function : Provides sequenced programmable power to a phased array radar test facility FeaturesTotal power subsystem integration Total power

Sorensen Power Supply MX Compliance Test System
Output Frequency

Sorensen Power Supply Compliance Test System
The Elgar TrueWave (TW) is designed for testing today's complex electronics, including avionics and commercial applications requiring DC and sine wave testing. The TW is ideal

Sorensen Power Supply Sorensen XG 1700 Watt
Product OverviewThe XG 1700 is an industry leading programmable DC power supply designed for test, production, laboratory, OEM and quality assurance applications. The XG 1700&nb

Sorensen Power Supply i-iX Series II
rms Output Currents

Sorensen Power Supply ETS TerraSAS
Product OverviewFor microgrids, energy storage, and inverter test applications, the TerraSASâ„¢ series photovoltaic (PV) simulators are specifically designed to emulate the dynamic elec